Home About Dorner Distributors TradeshowsSite Map
Dorner Advantage Newsletter

DORNER MFG. CORP.
975 Cottonwood Ave
P.O. Box 20
Hartland, WI 53029 USA

INSIDE THE USA
TEL: 800.397.8664
FAX: 800.369.2440

OUTSIDE THE USA
TEL: 262.367.7600
FAX: 262.367.5827

Home > Standard Products > 2200 Series > Cleated Belt End Drive

2200 SERIES CONVEYORS: Cleated Belt End Drive

2200 Series Belt Conveyors - Cleated Belt - End Drive


Specifications:

  • Loads up to 80 lbs* (36 kg)
  • Belt speeds up to 400 ft/min (122 m/min)
  • Belt widths: 1.75” (44 mm) to 24” (610 mm)
  • Conveyor lengths: 18” (457 mm) to 18’ (5,486 mm)
  • Cleats available from 0.24” (6 mm) to 2.36” (60 mm) high
  • 1.25” (32 mm) diameter drive and idler pulleys turn
    approximately 4.2” (107 mm) of belt per revolution
  • V-grooved stainless steel bedplate
  • 12 mm diameter integral drive shaft
  • models available

* Conveyor load capacity depends on conveyor size, incline,
motor position, accumulated loads and other factors.

Features/Benefits:

  • Quick five-minute belt change
  • Rack and pinion belt tensioning for fast, accurate single point belt tensioning
  • Aluminum die cast head plates eliminate painted surfaces
  • V-groove bedplate with guided belt provides positive belt tracking,
    even under demanding side load applications
  • Non V-guided belts use our patented belt tracking cams, offering you the
    widest belt selection possible
  • Strong, box-like construction resists damaging frame twist
  • 50% more belt take-up extends conveyor belt life
  • T-slots make mounting accessories simple with no drilling or special tools
  • Stand mounting brackets are easily re-positioned along the T-slot
  • Motion sensor ready
  • Sealed ball bearings

Optional: Dual or Idler End Output Shafts

Note: Standard idler pulley houses a small magnet which may be omitted upon request for magnetically sensitive products and applications.

STANDARD SIZES
Conveyor Width Reference 02 03 04 05 06 08 10 12 18 21 24
Conveyor Belt Width (W) 1.75”
(44)		 2.75”
(70)		 3.75”
(95)		 5”
(127)		 6”
(152)		 8”
(203)		 10”
(254)		 12”
(305)		 18”
(457)		 21”
(533)		 24”
(610)
Conveyor Length Reference 0150 0001 increments up to... 1800
Conveyor Length (L) 1.5’ (457) .12” (3) increments up to... 18’ (5,486)
Note: Lengths 13’ to 18’ available in widths 6” to 24” only.
Gang Drive Conveyors: Non-V-Guided belts up to 24” (610) wide, V-Guided belts up to 18” (457) wide

 

Notes:

  • Order gearmotor mounting packages and gearmotors separately - see Mount Packages and Gearmotors. For support stands and accessories - see Support Stands and Accessories.
  • Dimensions are represented in inches, feet, and (millimeters).
  • Due to the wide variety of drive set-ups and applications, point of installation guarding is the responsibility of the end user.
  • Conveyors longer than 12’ (3658mm) will be constructed using a multiple piece frame. Consult factory for locations of these frame joints. It is recommended that each frame joint be supported by a stand or other means.

 

Back to top