4100 Series Conveyors From Dorner Mfg. Corp.

STANDARD BELT SELECTION GUIDE						Standard belt material is stocked at Dorner, then cut & spliced at the factory for fast conveyor shipment.

01	A1	1A	FDA Accumulation	.067" (1.7)	Urethane	Polyester	212˚F (100˚C)	Low	X	X		Good	Packaging, clean room & inspection
02	A2	2A	General Purpose	.071” (1.8)	Urethane	Polyester	212˚F (100˚C)	Med	X	X		Good	Most versatile belt offering
03	A3	3A	FDA High Friction	.067” (1.7)	Urethane	Polyester	212˚F (100˚C)	High	X	X		Good	Packaging, clean room & inspection
05	A5	5A	Accumulation	.047” (1.2)	Urethane	Polyester	212˚F (100˚C)	V-Low	X	X		Good	Accumulation of products
06	A6	6A	Electrically Conductive	.063” (1.6)	Urethane	Polyester	176˚F (80˚C)	Low		X	X	Good	Electronics Handling
08	A8	8A	High Friction	.083” (2.1)	PVC	Polyester	158˚F (70˚C)	V-High		X		Poor	Conveys up to 35˚ inclines*

Note: See below for splice details. Plastic Clipper splice requires longer lead times. Belts with V-guiding may have a slight high spot or rib on the top surface. This rib would run longitudinally along the center of the belt. Consult factory with applications for which this may cause interference.
*Incline varies due to factors like dust, fluids and part material.

Belt Splicing

Finger Splice All belts are available with a standard Thermoformed finger splice. This splice makes the belt continuous and is virtually undetectable. Splice bonding methods vary by belt type. Consult factory for details.	Plastic Clipper* An optional plastic clipper splice is available for quick removal of belts or when conveyors are installed in tight spaces. The clipper does not protrude above the belt surface.	Metal Clipper* An optional metal clipper splice is also available for quick removal of belts or when conveyors are installed in tight spaces.

*See belt charts for compatibility. Not for use with 6200 Series bottom wiper option.
Plastic and Metal Clippers are slightly thicker than base belt. Consult factory for details.

SPECIALTY BELT SELECTION GUIDE							Specialty belt material is not stocked at Dorner and needs to be custom ordered for your special conveyor needs.

50			Heat Resistant		.05 (1.3)	Silicone	356˚F (180˚C)	Low		Good
53			Translucent & Nosebar, Accumulation		.02 (.51)	Urethane	212˚F (100˚C)	V-Low	X	Good	Back Lit inspection & Very Small Product Transfer
54	F4	4F	FDA Sealed Edge**	X	.06 (1.5)	Urethane	176˚F (80˚C)	Low	X	Good	Packaging, clean room & inspection
55	F5	5F	FDA Sealed Edge**	X	.06 (1.5)	Urethane	176˚F (80˚C)	High	X	Good	Packaging, clean room & inspection
56		6F	Cut Resistant	X	.08 (2.1)	Urethane	212˚F (100˚C)	Med		Good	Oily product release, Metal stamping
57		7F	Cut Resistant*	X	.10 (2.5)	Nitrile	176˚F (80˚C)	Med		Poor	Felt-like, dry metal stamping, glass & ceramic
58		8F	Cut Resistant		.06 (1.5)	Urethane	176˚F (80˚C)	Low		V-Good	Cross-linked surface, Gold colored
59		9F	Color Contrasting	X	.06 (1.5)	PVC	158˚F (70˚C)	Med		Poor	Black colored, hides overspray from ink jet
60		0G	Color Contrasting	X	.05 (1.3)	Urethane	212˚F (100˚C)	Low	X	Good	Green colored
61		1G	Color Contrasting	X	.05 (1.3)	Urethane	212˚F (100˚C)	Low	X	Good	Blue colored
63		3G	Electrically Conductive	X	.05 (1.2)	Urethane	176˚F (80˚C)	Low		Good	Static conductive, electronics handling
64		4G	High Friction	X	.17 (4.4)	PVC	194˚F (90˚C)	V-High		Poor
65		5G	Chemical Resistant	X	.05 (1.3)	Polypropylene	248˚F (120˚C)	Low	X	V-Good	V-Good Cut resistance, excellent product release
66		6G	Chemical Resistant	X	.07 (1.7)	Polyester	212˚F (100˚C)	Med	X	V-Good	Good Cut resistance, metal stamping apps

Note: Plastic Clipper splice requires longer lead times. Belts with V-guiding may have a slight high spot or rib on the top surface. This rib would run longitudinally along the center of the belt. Consult factory with applications for which this may cause interference.
*12" (305mm) wide conveyor maximum for non V-guided. ** Not available on 2” (51mm) wide conveyors.

4100 SERIES CONVEYORS: Belting

STANDARD BELT SELECTION GUIDE

Belt Splicing

SPECIALTY BELT SELECTION GUIDE