Home About Dorner Distributors TradeshowsSite Map
Dorner Advantage Newsletter

DORNER MFG. CORP.
975 Cottonwood Ave
P.O. Box 20
Hartland, WI 53029 USA

INSIDE THE USA
TEL: 800.397.8664
FAX: 800.369.2440

OUTSIDE THE USA
TEL: 262.367.7600
FAX: 262.367.5827

Home > Standard Products > 5200 Series > Curved Flat Belt End Drive

5200 SERIES CONVEYORS: Curved Flat Belt End Drive


Specifications:

  • Loads up to 500 lbs. (227 kg)
  • Belt speeds up to 260 ft/min (80 m/min)
  • Belt widths: 8" (203 mm) -36" (914 mm) in 2" increments
  • Conveyor lengths: to 99' (30,175 mm) in 1" increments
  • Curves available from 15° - 180° in 15° increments
  • UHMW wear strips
  • 4.3" diameter drive and idler pulleys
  • Two T-slots for mounting accessories
  • Rigid, 5.8" high, anodized aluminum frame

Features and Benefits:

  • Pre-engineered 15° curve segments makes reconfiguration quick and easy
  • QWIK slots make mounting air and electrical lines simple with no drilling, special tools, or t-nuts required
  • Belt with side tabs for true low side conveying accomodates larger than belt products
  • Inside and outside UHMW hold down rails
  • Completely contained belt eliminates catenary sag and reduces pinch points
  • Designed-in low voltage wireway provides support and protection for low voltage wires running from the electronic device
    to the main junction or control box
  • No holes in side rails makes reconfiguration quick and easy
  • Open top frame simplifies belt maintenance and replacement
  • Sprocket alignment key provides continuous sprocket alignment for quick belt assembly
  • Support stands mount directly to bottom of side rail which keeps frame open for mounting accessories
  • Nose bar tail option

Optional Interface Tail Section

  • Sealed bearing
  • 1 5/8 ” (41) diameter rollers
    provides 2 5/8 ” (67) diameter nose bar
  • Widths up to 36”
  • Both drive and idler
    tails available

 

 

Flush Top,
Low Side Frame

UHMW Belt
Tracking Guides

Support Stands Mount
Directly to Bottom of Frame

 

 

End Drive Model

 

 
Standard Sizes
Conveyor Width Reference 08 02 increments up to... 36
Conveyor Belt Width (W) 8” (203) 2” (51mm) increments up to... 36” (914mm)
Module Length Reference 020 001 increments up to... 999
Module Length (L) 20” (508) 1” (25mm) increments up to... 999” (25,375mm)

 

 

 

Nose Bar Drive Model

 

 
Belt Width Table
Conveyor Width (inch) Top of Belt Width Belt Width Including Tab Inside Radius of Belt Frame Width in Straight Frame Width in Curve
08 7.80 8.55 10.6 9.26 10.91
10 9.81 10.56 14.1 11.22 12.87
12 11.79 12.53 17.5 13.19 14.84
14 13.75 14.50 20.8 15.15 16.80
16 15.72 16.47 24.1 17.12 18.77
18 17.69 18.44 27.4 19.08 20.73
20 19.66 20.41 30.7 21.05 22.70
22 21.63 22.38 33.9 23.01 24.66
24 23.60 24.35 37.2 24.98 26.63
26 25.55 26.29 40.5 26.94 28.59
28 27.51 28.26 43.6 28.91 30.56
30 29.48 30.23 47.0 30.87 32.52
32 31.45 32.20 50.2 32.84 34.49
34 33.42 34.17 53.6 34.80 36.45
36 35.39 36.14 56.8 36.77 38.42

 

Notes:

  • Dimensions are represented in inches, feet, and (millimeters).
  • Due to the wide variety of drive set-ups and applications, point of installation guarding is the responsibility of the end user.


Part Reference Guide (2.90 MB PDF)

Back to top